Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

The influence of thermal residual stresses and thermal generated dislocation on the mechanical response of particulate-reinforced metal matrix nanocomposites

Due to thermal expansion mismatch between reinforcing particles and matrix, thermal induced dislocations are generated in metal matrix nanocomposites (MMNCs) during cooling down from the processing temperature. These dislocations have been identified as an important strengthening mechanism in particulate-reinforced MMNCs. In this study, the development of thermal residual stresses and thermal induced dislocations in MMNCs are predicted using discrete dislocation simulation, assuming the whole material is under uniform temperature change. Shear deformation is applied after the composites are cooled down to room temperature and the influence of thermal residual stresses and thermal generated dislocation on the overall response of particulate-reinforced MMNCs are investigated. The results show that the thermal residual stresses are high enough to generate dislocations and the dislocation density is higher in the interfacial region than the rest of the matrix. The predicted mechanical behavior of the MMNCs matches the experimental results better when thermal residual stresses are included in the simulations.     

电磁搅拌对大圆坯结晶器冶金行为影响的探讨

 为了探究结晶器电磁搅拌(M EMS)对大圆坯结晶器内综合冶金行为的影响。以大断面圆坯连铸结晶器冶金行为为研究对象，基于电磁热流体与凝固传输理论建立三维耦合数值模型。揭示大圆坯连铸常用五孔水口浇注条件下结晶器内电磁场、流场、传热与凝固等综合冶金行为，提出电磁搅拌对结晶器冶金性能影响的多参量评价方法。以中碳铬钼齿轮钢650 mm大圆坯连铸为例，指出结晶器电磁搅拌存在最佳搅拌电流，可获得相对较好的综合冶金效果。具体表现为弯月面保持一定的切向速度和过热度，有利于保护渣的熔化和夹杂物的上浮去除；液面波动幅度在控制范围内，可避免卷渣、改善表面质量；结晶器内钢液过热得到有效耗散，有利于等轴晶形核改善铸坯内部质量；侧孔出流钢液速度得到有效控制，可抑制注流对初凝坯壳的冲刷，提高了初生坯壳生长的均匀性。此外，电磁搅拌产生的水平旋流强度也可得到有效控制，有利于避免常见的皮下白亮带现象。     

湿式摩擦副滑摩过程温度场分析及实验验证

湿式摩擦副滑摩过程温度场与应力场相互耦合作用,温度场分布受到多种因素影响,其中压力、旋转速度、润滑流量作为湿式摩擦副工作参数对其温度场的影响尤为显著。在理论分析基础上,采用有限元数值模拟分析与实验研究相结合的方法,对摩擦界面温度场时空分布特性进行研究,同时研究界面温度场在摩擦副工作压力、相对转速和润滑流量作用下的变化规律。研究表明:在对偶钢片和摩擦片近外径侧更易出现高温和应力集中区,且对偶钢片相对于摩擦片更易出现温度和应力分布不均匀情况;温度场中高温集中区与应力场中应力集中区相对应,最大温度随着压力增加、相对转速增大、润滑流量减少而显著上升,该结果得到试验结果的验证。     

Characterizations of friction welding joint interface for AISI 316

Because of heat amount is different from peripheral to central of friction welding interface, which is leaded to vary the characterizations along that interface. Current study, respectively, focused on the effect of different friction pressure on micro-structural and mechanical properties of that friction welding joint interface. Presently, these friction pressures are 110, 130, 150 and 170 MPa while kept all other conditions constant. The effects of different friction pressure on welding interface characterization were investigated by EDX, SEM, tensile, compression, impact and hardness tests. The tensile tests carried out on the standardized test piece with diameter 6 mm and 8 mm, thus, compression tests were extracted from the positions of 0°, 45° 90° with test specimen of 4 mm diameter and 6.5 mm length at weld center. Whereas, the impact test pieces were picked up in two positions, the first one is symmetrical, which it obtained to the respect of the rotation axis and the interface, on the other hand, the second one is non-symmetrical with the axis of rotation and symmetrical to the interface, for making the notch head coincide with the center of the welded joint, The obtained results showed that with reducing of friction pressure will present lack of bonding increasing from peripheral toward the welding center, which will responsible on reducing of the mechanical properties such as tensile, compression and impact strength.     

粉土界面恒刚度循环剪切试验研究

竖向循环荷载作用下桩土界面的作用机理是研究桩土摩擦疲劳的关键。针对循环荷载作用下桩-粉土界面的剪切性能,使用改进的剪切试验装置在恒刚度条件下进行循环剪切试验,研究循环次数、累积位移和法向刚度对其摩擦疲劳性能、循环后单调剪切性能的影响。试验结果表明,粉土在循环剪切过程中,法向应力和剪应力在初始10个循环内随循环数增加快速衰减,随着循环进行,逐渐趋于稳定;单次循环内在剪切位移方向变化时,土体呈现表现出剪缩-剪胀-剪缩交替现象,总体变形呈现剪缩的趋势;循环荷载作用下,粉土界面的法向应力和剪应力随法向刚度增大衰减速率增大,达到稳定的累积循环位移越小;粉土循环后的单调剪切、法向应力恢复的单调剪切的剪应力比小于首次单调剪切试验值,且法向应力恢复的循环后剪切试验的剪胀程度较小,表明循环剪切过程中界面处粉土颗粒棱角破碎,颗粒变得光滑。在对试验数据分析的基础上,提出了与累积位移、法向刚度和初始应力相关的无量纲累积位移,建立了法向应力和界面摩擦角随累积位移的衰减方程。     

削减桩基负摩阻力的室内模拟试验

为探明桩基混凝土不同涂料对桩基负摩阻力的削减效果,通过大型剪切试验,以塑限18%的黏性土为试验土,着重研究了试验土含水率变化以及桩基混凝土侧面不同涂料对桩基负摩阻力的影响。结果表明,当黏性土含水率略大于塑限时,桩基负摩阻力的削减效果较好,此时在混凝土表面涂石蜡机油混合物、聚合物纳米材料或者油漆产生的削减效果基本一致;当黏性土含水率与塑限含水率相差较大时,采用石蜡机油混合物作为桩侧混凝土涂料对于桩基负摩阻力的削减效果最佳;可通过不同方式对中性点位置进行确定并采用不同适用条件下涂料对桩基负摩阻力进行削减。     

海水淡化用空心锥喷嘴喷淋性能理论及实验研究

设计开发一种具有高通量、低流阻特征的空心锥喷嘴,并通过理论与实验方法研究空心锥喷嘴的喷淋性能,基于准自由涡理论建立空心锥喷嘴内部流体流动的数学模型,阐明流量系数、喷淋锥角、喷嘴流量与喷嘴结构参数之间的定量关系,并利用多效蒸馏海水淡化喷淋实验台对理论计算结果进行实验测试和验证。研究结果表明:正常工作状态下喷嘴流量系数、喷淋锥角、喷淋流量等参数理论值与测量值之间的误差小于5%,验证了设计模型的准确性。同时根据实验测试数据,拟合得到该类型空心锥喷嘴喷淋锥角与雷诺数之间的经验公式,可为蒸馏海水淡化用大流量空心锥喷嘴的结构设计、工艺选型提供理论指导和数据支持。     

High-resolution FIB-TEM-STEM structural characterization of grain boundaries in the high dielectric constant perovskite CaCu3Ti4O12

In this work, the grain boundaries composition of the polycrystalline CaCu₃Ti₄O₁₂ (CCTO) was investigated. A Focused Ion Beam (FIB)/lift-out technique was used to prepare site-specific thin samples of the grain boundaries interface of CCTO ceramics. Scanning transmission electron microscopy (STEM) coupled with energy dispersive X-ray spectrometry (EDXS) and Electron Energy Loss Spectroscopy (EELS) systems were used to characterize the composition and nanostructure of the grain and grain boundaries region. It is known that during conventional sintering, discontinuous grain growth occurs and a Cu-rich phase appears at grain boundaries. This Cu-rich phase may affect the final dielectric properties of CCTO but its structure and chemical composition remained unknown. For the first time, this high-resolution FIB-TEM-STEM study of CCTO interfacial region highlights the composition of the phases segregated at grain boundaries namely CuO, Cu₂O and the metastable phase Cu₃TiO_4.